presents:
Industrial Floor Booths

Industrial Floor Booth Design
Floor spray booths feature a modular design. Modularization offers the economy of a standardized line of spray booths, while making available a variety of sizes and configurations to fit a broad range of finishing processes. The three primary modules (working depths, arresting filters, and exhaust chambers) are offered in heights of 7, 8, 10, and 12 feet, and in sixteen widths from 6 to 20 feet. Working depth extensions are available in increments of 2 feet and 3 feet to accommodate most finishing operations fabricated from corrosion-resistant, galvanized steel for protection against rust and corrosion. With proper surface preparation, they can be painted after installation. Fast-Pak booths are shipped within 7 to 10 days after acceptance of the order.

NOTE: Our booths have pre-punched flanged panels with a fold-back and are assembled with Grade 5 nuts and bolts. Many competitor brands require assembly with Tek Screws. Not only is it difficult to get the Tek Screws to be uniform, invariably the panels will not hang square. This is a serious problem when it becomes time to hang booth doors. The combination of keeping Tek Screws uniform and panels square adds 50% to the assembly time.

Industrial floor spray booths are FOB: Osseo, WI.
Open Face Filter Booths

Easy Assembly
The ProClean's tough 18-gauge corrosion resistant panels are designed for fast, easy assembly, while creating a strong, rigid structure. High quality assembly hardware and illustrated assembly instructions are included.


Global Finishing SolutionsTM Booth Packages Include the Following

  • Quick Ship Program, 5 to 7 days on Fast-Pak series.
  • Detailed mechanical and electrical instructions or drawing.
  • 18 Gauge Pre-Punched Galvanized Panels, Tie-In angles are 14 Gauge.
  • Grade 5 hardware and caulk.
  • Top or Rear Exhaust Outlet.
  • Minimum of one four tube overhead light fixture with 32 watt tubes and inside access. Class 1 Division II, UL Listed.
  • Totally enclosed fan cooled (T.E.F.C.) Motor 208/230/460V/3Ph/60Hz, UL listed.
  • Manometer
  • First Set of Polyester Paint Pocket Filters.
  • Booth conforms to the requirements of: NFPA-33, OSHA, UFC45, and SQAQMD.
  • Installer or Contractor will make certain that all of the electrical wiring, conduit, piping, gas supply, roof penetrations and automatic fire protection systems conform to applicable codes.
  • Fire suppression system is not included with the standard booth but is required by NFPA-33.
Popular Size Global Finishing SolutionsTM Floor Spray Booths

Contact us for booth sizes other than those shown.

P/N
Price
Working
Dimensions
Overall
Dimensions
# of Lights Overhead
Fan Dia.
Motor HP
Height
Width
Depth
Height
Width
Depth
IFPG-060706 $2600.00 7' 6' 6' 7'-2" 6'-4" 9'-2" 1 24" 1
IFPG-080706 $2920.00 7' 8' 6' 7'-2" 8'-4" 9'-2" 1 24" 2
IFPG-100706 $3925.00 7' 10' 6' 7'-2" 10'-4" 9'-2" 2 30" 2
IFPG-120706 $4495.00 7' 12' 6' 7'-2" 12'-4" 9'-2" 2 34" 2
IFPG-060806 $2850.00 8' 6' 6' 8'-2" 6'-4" 9'-2" 1 24" 2
IFPG-080806 $3650.00 8' 8' 6' 8'-2" 8'-4" 9'-2" 1 30" 1
IFPG-100806 $4065.00 8' 10' 6' 8'-2" 10'-4" 9'-2" 2 30" 2
IFPG-120806 $4730.00 8' 12' 6' 8'-2" 12'-4" 9'-2" 2 34" 3
IFPG-061006 $3105.00 10' 6' 6' 10'-2" 6'-4" 9'-2" 1 24" 2
IFPG-081006 $4000.00 10' 8' 6' 10'-2" 8'-4" 9'-2" 1 30" 2
IFPG-101006 $4460.00 10' 10' 6' 10'-2" 10'-4" 9'-2" 2 30" 3
 IFPG-121006  $5205.00 10' 12' 6' 10'-2" 12'-4" 9'-2" 2 34" 5

Allow 30" to booth height for top exhaust or 30" to booth depth for back exhaust, if fan and motor are located inside building.

Options: Global Finishing SolutionsTM Spray Booth

  • The standard filter media is 20" x 20" paint pocket pads.
  • Side openings for conveyors, with 125 or 150 FPM fan velocity.
  • 4' Side Light Fixtures, Class I, Division II four tube Fixtures, 32 Watt Tube, ETL Listed. 120/277 volt inside access. $318.41 each with panel cut-out.
  • Extension to working depth in 2 & 3' depths, with our without additional overhead lights.
  • Standard fan motor specification is 208/230/460V/3PH/60hz. totally enclosed fan cooled, (T.E.F.C.). Optional single phase as well as explosion proof motors are available at an additional charge.
  • Optional NEMA 1 control panels or component packages including fused disconnect, motor starter, fan and light switches.
  • Optional air solenoid, with exhaust port muffler, to provide air to the spraygun only when the booth fan is operating. Part number 242-019 $219.50.
  • Optional exhaust stack components, see below.
  • Optional air make-up units are available mounted indoors or outdoors, and can be provided as vertical or horizontal units.

Exhaust Stack Options

Description
18"
24"
30"
34"
P/N
Price
P/N
Price
P/N
Price
P/N
Price
Flanged connector ring
FR-1811
$40.10
FR-2411
$53.20
409-130
$59.75
FR-3411
$66.30
Plain 3' Stack
DU-PLP-18
$62.55
DU-PLP-24
$83.10
DU-PLP-30
$102.70
DU-PLP-34
$126.95
Plain 3' Stack with door
DU-PLP-18W/DOOR
$109.20
DU-PLP-24W/DOOR
$139.10
DU-PLP-30W/DOOR
$158.75
DU-PLP-34W/DOOR
$184.00
Elbow 45 Degrees
DU-E45-18
$121.35
DU-E45-24
$159.75
DU-E45-30
$180.25
DU-E45-34
$217.50
Elbow 90 Degrees
DU-E90-18
$186.75
DU-E90-24
$224.00
DU-E90-30
$361.25
DU-E90-34
$353.75
Wall Shutter
DU-SHW-18
$122.30
DU-SHW-24
$145.60
DU-SHW-30-30
$183.00
DU-SHW-34
$311.75
Flat Roof Flange with Collar**
DU-FRF-18
$206.50
DU-FRF-24
$229.75
DU-FRF-30-WC
$240.00
DU-FRF-34
$264.256
Guy Wire Kit
DU-GWK-18
$95.20
DU-GWK-24
$98.00
DU-GWK-30
$98.00
DU-GWK-34
$98.00
Stack Head with Auto Damper
DU-ARV-18
$382.75
DU-ARV-24
$393.00
DU-ARV-30
$410.75
DU-ARV-34
$416.50


** Note: Our flat roof flashings will not work on corrugated steel roofs. A custom flashing will have to be fabricated locally.

** Note: Spray Booths, Booth components, and parts shipped to the following States are subject to the appropriate State or County tax unless your company can provide documentation of being tax exempt. These States are : AL, AZ, CA, CO, FL, GA, IL, IN, IA, KS, MD, MA, MI, MN, NE, NV, NC, ND, OH, OK, PA, RI, SC, SD, TN, TX, UT, VA, WA, WV, WI, and WY.

BEWARE of design and specification differences between GLOBAL FINISHING SOLUTIONS and other makes of booths. If they do not mention these design and or specifications they may not be proving them.

  • 2" flanged panel with rolled edge for additional strength, 18 gauge G90 galvanized.
  • Reinforced and supported roof panels on booths wider than 12'.
  • Punched panels on CNC equipment for exact alignment with nut & bolt assembly.
  • Full height filter wall, not partial.
  • Sparkless fan blade with variable pitch pulley, AND FAN GUARD.
  • "Listed" Class 1, Division 2 light fixture such as ETL or UL. INSIDE ACCESS, 32 watt with 85 CRI color correctable tubes.
  • Optional exhaust filter media.
  • Totally enclosed fan cooled (TEFC) 208/230/460 tri-voltage 3-phase fan motor.
  • Fire curtain with NFPA & OSHA Warning Decals.
  • Manometer.
  • Complete assembly instructions and necessary hardware.



Content Copyright © 1997-2014 by  Auto Finish Systems, 2691 S. Calhoun Road, New Berlin, WI 53151 - 262-784-5977     online.